November Sale - 5% OFF - Code: NOV5
Price Match Guarantee
Free Shipping on Orders Over $50
No Minimum Order
Deals: $5 off orders over $100 with code 5OFF, $10 off orders over $200 with code 10OFF, $25 off orders over $500 with code 25OFF

Thermostats

(41 Styles Available)
  • Ships Factory Direct
  • Full Manufacturer Warranty
  • 30 Day Money Back Guarantee
  • Price Match Guarantee

Thermostats

(41 Styles Available)
  • Ships Factory Direct
  • Full Manufacturer Warranty
  • 30 Day Money Back Guarantee
  • Price Match Guarantee

Frequently Asked Questions

How does a thermostat work?

Thermostats work by controlling the flow of hot or cold air and maintaining a set temperature. They operate on thermostat sensors, which sense the room temperature. For more information, read this article on how thermostats work.

How do I replace a thermostat?

  1. Turn off the HVAC control panel.
  2. Dislodge the old thermostat cover.
  3. Disconnect the wires of the old thermostat.
  4. Remove the old thermostat.
  5. Install the base of the new thermostat.
  6. Connect the thermostat’s wires.
  7. Mount the new thermostat, along with the thermostat cover, on its base.

What temperature should I set my thermostat in winter?

According to the U.S. Department of Energy, the optimal temperature when setting a thermostat is 68 degrees Fahrenheit.

How do I tell if a thermostat is bad?

Some of the signs that tell if a thermostat is not working include:
  • It can’t turn on or off the HVAC system.
  • It can’t detect the room temperature.
  • It is unresponsive.

What's the difference between hold and run in thermostats?

In programmable thermostats, smart thermostats, and wireless thermostats, pressing the hold button overrides the programmed temperature. The run button allows these digital thermostats to return to their programmed temperature and schedule.

What is a line voltage thermostat?

A line voltage thermostat switches the full supply voltage going to an electric heater, usually 120V, 240V or 277V. It is wired in series with the heater and carries its current. Most TPI thermostats in this category are rated 22 amps at 120 to 240V. Low voltage thermostats, such as the TH115A024T, run on 24V and signal a relay or control board instead. Never connect a low voltage thermostat to line voltage.

Do I need a single pole or double pole thermostat?

On a 120V circuit, a single pole thermostat is common. On 240V or 208V circuits, both wires are live, and a single pole model leaves one leg energized even when set to off. A double pole thermostat with positive off, such as the ET9DTS or 32T2, disconnects both legs when turned fully off. Many installers prefer double pole for 240V heaters. Confirm local requirements with your electrician.

Can one thermostat control more than one heater?

Yes, as long as the total current stays within the thermostat's rating. Add up the amps of every heater it will switch. A 22 amp thermostat can run several small baseboard heaters, but larger loads need a relay or contactor that the thermostat controls. Heater control panels and low voltage relays are common solutions for zones with many heaters.

What is a hazardous location thermostat?

It is a thermostat built for areas where flammable gases, vapors or dusts may be present, such as fuel handling or chemical storage rooms. TPI's HLT and EPET models use a thick cast aluminum housing with threaded conduit entries. The thermostat's class, group and division rating must match the area classification set by the facility's engineer. Check the rating on each spec sheet before ordering.

Which thermostat temperature range do I need?

Pick a range that covers your target setpoint with room to spare. Comfort heating fits the 50 to 90°F range on most ET9 models. Freeze protection in pump houses, sheds or warehouses is easier with a lower range, such as the 35 to 75°F ET9S4TS and ET9D4TS. Built-in baseboard thermostats like the TBS and 3900T1 read 0 to 110°F.

Thermostats

Thermostats for electric heat

This category covers TPI thermostats made mainly for electric heaters. Most are line voltage thermostats. They carry the heater's full current through their contacts, typically 22 amps at 120 to 240V and 18 amps at 277V. A smaller group are low voltage or wireless controls that switch a relay or control board instead. The right choice starts with the heater it will control.

Built-in and heater-specific thermostats

Some thermostats mount inside the heater itself. The TBS (single pole) and TBD (double pole) are in-built baseboard thermostats. The 3900T1 and 3900T2 fit TPI hydronic and architectural electric baseboard heaters, in white or in brown as the 3900T1C and 3900T2C. Their range is 0 to 110°F. Other kits are made for one heater line: the 32T1 and 32T2 for the 3200 Series midsized fan-forced wall heater, and the T5100 and T5102 for 5100 Series fan-forced heaters from 3.3 to 20 kW.

Wall-mount line voltage thermostats

The ET9 Series covers the common jobs. Options include SPST heat only (ET9STS, ET9SWTS), DPST heat only with positive off (ET9DTS, ET9DWTS), SPDT heat or cool (ETD9STS), 2-stage heat (ET9MTS), 2-stage heat with 1-stage cool (ETD9MTS) and cool only (ET9SRTS). Most read 50 to 90°F. The ET9S4TS and ET9D4TS read 35 to 75°F for cooler spaces. Other choices include the TW145 and TW146 tamper-resistant thermostats and the 25 amp, 277V D2025H10BA from the 2000 Series.

Industrial, washdown and hazardous location

KT Series industrial thermostats (KT110, KT121, KTD110, CKTD110) have rugged steel housings, and the KT121 comes with a 6-foot cord and plug. The TW155A and TW255A remote washdown thermostats are NEMA 4X raintight with stainless steel hardware. For hazardous locations, the HLT1, HLT2 and EPET models use a half-inch-thick cast aluminum housing tapped for 3/4-inch conduit. EPETD8 models are rated 120 to 277 VAC and EPETP8 models 120 to 480 VAC.

Programmable and low voltage

The TL8230A1003 is a programmable line voltage DPST thermostat for 240/208V electric heat. The TH115A024T is a 7-day, heat-only low voltage programmable model. The RFKIT-5 is a wireless transmitter and relay kit for Hotpod duct heaters.

How to choose

  • Load: the thermostat's amp rating must meet or exceed the heater's current draw. Larger loads need a relay or contactor.
  • Poles: a single pole thermostat opens one leg of the circuit. A double pole model with positive off opens both, which fully disconnects a 240V heater.
  • Function: heat only, cool only, heat or cool, or two-stage.
  • Environment: use washdown or hazardous location models where the space calls for them, and match the location rating on the spec sheet.
  • Mounting: built-in, wall-mount or remote sensing.

Guards, sensors and relays are in thermostat parts and accessories. Systems with several heaters can use heater control panels. Have a licensed electrician confirm wiring and circuit size.

GET $5 OFF

FOR YOUR FIRST ORDER INSTANTLY

⟩

I’m not interested in saving money on my order

Enjoy Your Coupon Code Now!

Shop with confidence, your satisfaction is guaranteed.
⟩
WELCOME5 SHOP NOW